[Rear-users] ReaR 1.5pre1

Christian Neuhold cuniculus at inode.at
Sat Mar 17 11:02:08 CET 2007


Hi again,

when i set ifenslave bond0 eth0 eth1 manually, network works.

Should rear do this for me ?

Ciao
	cuni

Am Samstag, 17. März 2007 10:32:55 schrieb Christian Neuhold:
> Hi,
>
> bonding device is up and running. (local ping is working)
>
> Ciao
> 	cuni
>
> Am Freitag, 16. März 2007 12:30:05 schrieb Schlomo Schapiro:
> > Hi,
> >
> > thanks for testing !
> >
> > Maybe the bonding device is not "up" ?
> >
> > Regards,
> > Schlomo
> >
> > Christian Neuhold wrote:
> > > Hello,
> > >
> > > I tried out your new version. Backup and restore is working great on
> > > CentOS 4.4. I tested it
> > > - with software raid
> > > - without software raid
> > > - with vg and filesystem exclude
> > > - without vg and filesystem exclude
> > >
> > > I used for restore TSM. PXE and ISO is also working.
> > >
> > > But I have to bind ip address manually. Bonding is not working. I have
> > > to check it why. Because device and IP adress exists, but I can't ping
> > > any other linux machines.
> > >
> > > Best Regards
> > > 	Cuni
> > >
> > > Am Montag, 12. März 2007 00:08:01 schrieb Schlomo Schapiro:
> > >> Hi,
> > >>
> > >> attached please find rear 1.5pre1 which should solve the following
> > >> issues: - bonding
> > >> - md devices on non-SUSE
> > >> - cciss
> > >> - TSM should also backup the resulting files
> > >>
> > >> Please give it a try and send me the feedback (positive & negative).
> > >>
> > >> Regards,
> > >> Schlomo
> > >>
> > >> PS: Christian, I couldn't run a full test on your VM sine it lacks
> > >> some crucial software (mount.cifs, mkisofs usw.). But the rear
> > >> mkrescue ran through cleanly now and the data files in
> > >> /etcc/rear/recovery look good to me. So please kindly check this RPM
> > >> on the CentOS VM you have and also do a real backup/recovery.
> > >>
> > >> Christian Neuhold wrote:
> > >>> Hi,
> > >>>
> > >>> i only make a minimal rear configuration, I hope this is ok.
> > >>> My root filesystem is on a logical volume.
> > >>> rear backup command I use: rear -d -D mkbackup
> > >>>
> > >>> vol_id does not exist in Centos 4.4, instead I use udev_volume_id,
> > >>> but I get "error DEVPATH empty" always.
> > >>>
> > >>> udev_volume_id  /dev/mapper/rootvg-root_lv
> > >>> error DEVPATH empty
> > >>>
> > >>> udev_volume_id /dev/rootvg/rootlv
> > >>> error DEVPATH empty
> > >>>
> > >>> udev_volume_id  /dev/sdc
> > >>> error DEVPATH empty
> > >>>
> > >>>
> > >>>
> > >>> local.conf
> > >>> OUTPUT=TSM
> > >>> MODULES_LOAD=( vmxnet )
> > >>>
> > >>> /proc/partitions
> > >>> major minor  #blocks  name
> > >>>
> > >>>    8     0    2097152 sda
> > >>>    8     1     152586 sda1
> > >>>    8     2    1943865 sda2
> > >>>    8    16    2097152 sdb
> > >>>    8    17     152586 sdb1
> > >>>    8    18    1943865 sdb2
> > >>>    9     0     152512 md0
> > >>>    9     1    1943744 md1
> > >>>  253     0     262144 dm-0
> > >>>  253     1     131072 dm-1
> > >>>  253     2     950272 dm-2
> > >>>  253     3     425984 dm-3
> > >>>  253     4     131072 dm-4
> > >>>    8    32     229376 sdc
> > >>>  253     5      53248 dm-5
> > >>>
> > >>> fstab:
> > >>> # This file is edited by fstab-sync - see 'man fstab-sync' for
> > >>> details /dev/rootvg/rootlv      /                       ext3   
> > >>> defaults 1 1 /dev/md0                /boot                   ext3   
> > >>> defaults 1 2 none                    /dev/pts                devpts
> > >>> gid=5,mode=620  0 0 none                    /dev/shm
> > >>> tmpfs defaults        0 0 none                    /proc
> > >>> proc    defaults        0 0 none                    /sys
> > >>>   sysfs   defaults        0 0 /dev/rootvg/tmp_lv      /tmp
> > >>>     ext3    defaults        1 2 /dev/rootvg/usr_lv      /usr
> > >>>       ext3    defaults        1 2 /dev/rootvg/var_lv      /var
> > >>>         ext3    defaults        1 2 /dev/rootvg/swap_lv     swap
> > >>>           swap    defaults        0 0 /dev/datavg/prod_lv    
> > >>> /srv/prod ext3    defaults,noauto 0 0 /dev/hdc
> > >>> /media/cdrom            auto
> > >>> pamconsole,exec,noauto,managed 0 0
> > >>> /dev/fd0                /media/floppy           auto
> > >>> pamconsole,exec,noauto,managed 0 0
> > >>>
> > >>>
> > >>> /tmp/rear.log
> > >>> 2007-02-13 20:31:35 Relax & Recover Version 1.4 / 2007-02-06
> > >>> 2007-02-13 20:31:35 Combining configuration files
> > >>> 2007-02-13 20:31:35 Skipping /etc/rear/mkbackup.conf (file not found
> > >>> or empty) 2007-02-13 20:31:35 Including /etc/rear/Linux-i386.conf
> > >>> 2007-02-13 20:31:35 Including /etc/rear/GNU/Linux.conf
> > >>> 2007-02-13 20:31:35 Skipping /etc/rear/CentOS.conf (file not found or
> > >>> empty) 2007-02-13 20:31:35 Skipping /etc/rear/CentOS/i386.conf (file
> > >>> not found or empty)
> > >>> 2007-02-13 20:31:35 Skipping /etc/rear/CentOS/4.4.conf (file not
> > >>> found or empty)
> > >>> 2007-02-13 20:31:35 Including /etc/rear/site.conf
> > >>> 2007-02-13 20:31:35 Including /etc/rear/local.conf
> > >>> 2007-02-13 20:31:36 Creating build area '/tmp/rear.4065'
> > >>> 2007-02-13 20:31:36 Running mkbackup workflow
> > >>> 2007-02-13 20:31:36 Running 'prep' stage
> > >>> 2007-02-13 20:31:36 Including prep/default/01_progress_start.sh
> > >>> 2007-02-13 20:31:36 Including prep/TSM/default/40_prep_tsm.sh
> > >>> 2007-02-13 20:31:36 Including prep/default/99_progress_stop.sh
> > >>> 2007-02-13 20:31:36 Finished running 'prep' stage in 0 seconds
> > >>> 2007-02-13 20:31:36 Running 'dr' stage
> > >>> 2007-02-13 20:31:36 Including dr/default/01_mk_config_dir_recovery.sh
> > >>> 2007-02-13 20:31:36 Including
> > >>> dr/GNU/Linux/10_describe_physical_devices.sh 2007-02-13 20:31:36
> > >>> Skipping small removable device 'hdc' [Size: 3GB]. Adjust
> > >>> SYSFS_REMOVABLE_DEVICE_SIZE [15] to prevent
> > >>> this.
> > >>> 2007-02-13 20:31:36 Including
> > >>> dr/GNU/Linux/11_describe_mountpoint_device.sh 2007-02-13 20:31:36
> > >>> Including dr/GNU/Linux/12_describe_filesystems.sh 2007-02-13 20:31:36
> > >>> ERROR Cannot determine filesystem info
> > >>> on '/dev/mapper/rootvg-rootlv'
> > >>> Your udev implementation (vol_id or udev_volume_id) does not
> > >>> recognize it. [root at CNCCENTOS01 /]# rm -rf /tmp/rear.*
> > >>> rear mkbackup -d
> > >>> [root at CNCCENTOS01 /]# rear -d -D mkbackup
> > >>> Relax & Recover Version 1.4 / 2007-02-06
> > >>> The preparation phase OK
> > >>> ERROR: Cannot determine filesystem info on
> > >>> '/dev/mapper/rootvg-rootlv' Your udev implementation (vol_id or
> > >>> udev_volume_id) does not recognize it. [root at CNCCENTOS01 /]# cat
> > >>> /tmp/rear.
> > >>> cat: /tmp/rear.: No such file or directory
> > >>> [root at CNCCENTOS01 /]# cat /tmp/rear.log
> > >>> 2007-02-13 20:31:51 Relax & Recover Version 1.4 / 2007-02-06
> > >>> 2007-02-13 20:31:51 Combining configuration files
> > >>> 2007-02-13 20:31:51 Skipping /etc/rear/mkbackup.conf (file not found
> > >>> or empty) 2007-02-13 20:31:51 Including /etc/rear/Linux-i386.conf + .
> > >>> /etc/rear/Linux-i386.conf
> > >>> ++ REQUIRED_PROGS=("${REQUIRED_PROGS[@]}" sfdisk)
> > >>> ++ PROGS=("${PROGS[@]}" grub partprobe parted lilo fdisk cfdisk)
> > >>> + test 1
> > >>> + set +x
> > >>> 2007-02-13 20:31:51 Including /etc/rear/GNU/Linux.conf
> > >>> + . /etc/rear/GNU/Linux.conf
> > >>> ++ PROGS=(${PROGS[@]} bash mknod vol_id udev_volume_id portmap
> > >>> readlink rpcinfo grep cat tr reboot halt shutdown killall5
> > >>> killall chroot tee awk ip ifenslave klogd syslog-ng syslogd echo cp
> > >>> date wc cut rm test init ethtool expand sed mount umou
> > >>> nt insmod modprobe lsmod true false mingetty rmmod hostname uname
> > >>> sleep logger ps ln dirname basename mkdir cpio tty ping
> > >>> netstat free traceroute less vi rmmod df ls dmesg du tar gzip netcat
> > >>> top iptraf joe pico getent id nslookup ldd strace rsy
> > >>> nc tail head find md5sum mkfs mkfs.ext2 mkfs.ext3 mkfs.jfs mkfs.xfs
> > >>> mkfs.reiserfs mkreiserfs fsck.ext2 fsck.ext3 fsck.xfs
> > >>> fsck.reiserfs reiserfsck tune2fs xfs_admin xfs_db jfs_tune
> > >>> reiserfstune fsck expr egrep grep fgrep df chmod chown stat mks
> > >>> wap swapon swapoff mknod)
> > >>> ++ LIBS=(${LIBS[@]} /lib/libnss_dns* /lib/libnss_files*
> > >>> /lib/libgcc_s*) ++ MODULES=(${MODULES[@]} af_packet unix nfs lockd
> > >>> sunrpc cifs) ++
> > >>> COPY_AS_IS=(${COPY_AS_IS[@]} /dev /etc/protocols /etc/services
> > >>> /etc/rpc /etc/termcap /usr/share/terminfo) + test 1
> > >>> + set +x
> > >>> 2007-02-13 20:31:51 Skipping /etc/rear/CentOS.conf (file not found or
> > >>> empty) 2007-02-13 20:31:51 Skipping /etc/rear/CentOS/i386.conf (file
> > >>> not found or empty)
> > >>> 2007-02-13 20:31:51 Skipping /etc/rear/CentOS/4.4.conf (file not
> > >>> found or empty)
> > >>> 2007-02-13 20:31:51 Including /etc/rear/site.conf
> > >>> + . /etc/rear/site.conf
> > >>> + test 1
> > >>> + set +x
> > >>> 2007-02-13 20:31:51 Including /etc/rear/local.conf
> > >>> + . /etc/rear/local.conf
> > >>> ++ OUTPUT=TSM
> > >>> ++ MODULES_LOAD=(vmxnet)
> > >>> + test 1
> > >>> + set +x
> > >>> 2007-02-13 20:31:51 Creating build area '/tmp/rear.4263'
> > >>> 2007-02-13 20:31:51 Running mkbackup workflow
> > >>> 2007-02-13 20:31:51 Running 'prep' stage
> > >>> 2007-02-13 20:31:51 Including prep/default/01_progress_start.sh
> > >>> + . /usr/share/rear/prep/default/01_progress_start.sh
> > >>> ++ ProgressStart 'The preparation phase'
> > >>> ++ echo -n 'The preparation phase  '
> > >>> ++ kill -USR2 4296
> > >>> + test 1
> > >>> + set +x
> > >>> 2007-02-13 20:31:51 Including prep/TSM/default/40_prep_tsm.sh
> > >>> + . /usr/share/rear/prep/TSM/default/40_prep_tsm.sh
> > >>> ++ COPY_AS_IS=("${COPY_AS_IS[@]}" "${COPY_AS_IS_TSM[@]}")
> > >>> ++
> > >>> COPY_AS_IS_EXCLUDE=("${COPY_AS_IS_EXCLUDE[@]}"
> > >>> "${COPY_AS_IS_EXCLUDE_TSM[@]}") ++ PROGS=("${PROGS[*]}"
> > >>> "${PROGS_TSM[*]}")
> > >>> + test 1
> > >>> + set +x
> > >>> 2007-02-13 20:31:51 Including prep/default/99_progress_stop.sh
> > >>> + . /usr/share/rear/prep/default/99_progress_stop.sh
> > >>> ++ ProgressStop
> > >>> ++ kill -USR1 4296
> > >>> ++ echo -e '\bOK'
> > >>> + test 1
> > >>> + set +x
> > >>> 2007-02-13 20:31:51 Finished running 'prep' stage in 0 seconds
> > >>> 2007-02-13 20:31:51 Running 'dr' stage
> > >>> 2007-02-13 20:31:51 Including dr/default/01_mk_config_dir_recovery.sh
> > >>> + . /usr/share/rear/dr/default/01_mk_config_dir_recovery.sh
> > >>> ++ rm -Rf /etc/rear/recovery
> > >>> ++ mkdir -m 755 /etc/rear/recovery
> > >>> + test 1
> > >>> + set +x
> > >>> 2007-02-13 20:31:51 Including
> > >>> dr/GNU/Linux/10_describe_physical_devices.sh + .
> > >>> /usr/share/rear/dr/GNU/Linux/10_describe_physical_devices.sh ++
> > >>> FindPhysicalDevices
> > >>> +++
> > >>> ls -d /sys/block/hdc/device /sys/block/sda/device
> > >>> /sys/block/sdb/device /sys/block/sdc/device ++ for d in '$(ls -d
> > >>> /sys/block/*/device)' ++ test -L /sys/block/hdc/device
> > >>> +++ dirname /sys/block/hdc/device
> > >>> ++ sysfspath=/sys/block/hdc
> > >>> +++ basename /sys/block/hdc
> > >>> ++ device=hdc
> > >>> ++ test -s /sys/block/hdc/size
> > >>> +++ cat /sys/block/hdc/size
> > >>> ++ sysfssize=8388604
> > >>> +++ cat /sys/block/hdc/removable
> > >>> ++ test 1 -eq 1 -a 3 -le 15
> > >>> ++ Log 'Skipping small removable device '\''hdc'\'' [Size: 3GB].
> > >>> Adjust SYSFS_REMOVABLE_DEVICE_SIZE [15] to prevent this.'
> > >>> ++ test 1 -gt 0
> > >>> +++ Stamp
> > >>> +++ date '+%Y-%m-%d %H:%M:%S '
> > >>> ++ echo '2007-02-13 20:31:51 Skipping small removable device
> > >>> '\''hdc'\'' [Size: 3GB]. Adjust SYSFS_REMOVABLE_DEVICE_SIZE [
> > >>> 15] to prevent this.'
> > >>> 2007-02-13 20:31:51 Skipping small removable device 'hdc' [Size:
> > >>> 3GB]. Adjust SYSFS_REMOVABLE_DEVICE_SIZE [15] to prevent
> > >>> this.
> > >>> ++ continue
> > >>> ++ for d in '$(ls -d /sys/block/*/device)'
> > >>> ++ test -L /sys/block/sda/device
> > >>> +++ dirname /sys/block/sda/device
> > >>> ++ sysfspath=/sys/block/sda
> > >>> +++ basename /sys/block/sda
> > >>> ++ device=sda
> > >>> ++ test -s /sys/block/sda/size
> > >>> +++ cat /sys/block/sda/size
> > >>> ++ sysfssize=4194304
> > >>> +++ cat /sys/block/sda/removable
> > >>> ++ test 0 -eq 1 -a 2 -le 15
> > >>> ++ DeviceNameToNode sda
> > >>> ++ device=/dev/sda
> > >>> ++ device2=/dev/sda
> > >>> ++ test -b /dev/sda
> > >>> ++ echo /dev/sda
> > >>> ++ for d in '$(ls -d /sys/block/*/device)'
> > >>> ++ test -L /sys/block/sdb/device
> > >>> +++ dirname /sys/block/sdb/device
> > >>> ++ sysfspath=/sys/block/sdb
> > >>> +++ basename /sys/block/sdb
> > >>> ++ device=sdb
> > >>> ++ test -s /sys/block/sdb/size
> > >>> +++ cat /sys/block/sdb/size
> > >>> ++ sysfssize=4194304
> > >>> +++ cat /sys/block/sdb/removable
> > >>> ++ test 0 -eq 1 -a 2 -le 15
> > >>> ++ DeviceNameToNode sdb
> > >>> ++ device=/dev/sdb
> > >>> ++ device2=/dev/sdb
> > >>> ++ test -b /dev/sdb
> > >>> ++ echo /dev/sdb
> > >>> ++ for d in '$(ls -d /sys/block/*/device)'
> > >>> ++ test -L /sys/block/sdc/device
> > >>> +++ dirname /sys/block/sdc/device
> > >>> ++ sysfspath=/sys/block/sdc
> > >>> +++ basename /sys/block/sdc
> > >>> ++ device=sdc
> > >>> ++ test -s /sys/block/sdc/size
> > >>> +++ cat /sys/block/sdc/size
> > >>> ++ sysfssize=458752
> > >>> +++ cat /sys/block/sdc/removable
> > >>> ++ test 0 -eq 1 -a 0 -le 15
> > >>> ++ DeviceNameToNode sdc
> > >>> ++ device=/dev/sdc
> > >>> ++ device2=/dev/sdc
> > >>> ++ test -b /dev/sdc
> > >>> ++ echo /dev/sdc
> > >>> + test 1
> > >>> + set +x
> > >>> 2007-02-13 20:31:51 Including
> > >>> dr/GNU/Linux/11_describe_mountpoint_device.sh + .
> > >>> /usr/share/rear/dr/GNU/Linux/11_describe_mountpoint_device.sh ++ echo
> > >>> -n ''
> > >>> ++++ mount
> > >>> ++++ cut -d ' ' -f 1,3
> > >>> ++++ grep -v noauto /etc/fstab
> > >>> +++ join -a 2 -j 2 /dev/fd/63 /dev/fd/62
> > >>> ++ read -a entry
> > >>> ++++ grep -v '^#'
> > >>> ++++ tr -s ' \t' ' '
> > >>> ++++ cut -s -d ' ' -f 1,2,3
> > >>> ++++ sort -k 2
> > >>> ++++ sort -k 2 -t ' '
> > >>> ++++ grep -E '(reiserfs|xfs|ext|jfs)'
> > >>> ++ IsInArray / /srv/prod
> > >>> ++ search=/
> > >>> ++ shift
> > >>> ++ test 1 -gt 0
> > >>> ++ test / = /srv/prod
> > >>> ++ shift
> > >>> ++ test 0 -gt 0
> > >>> ++ return 1
> > >>> ++ IsInArray /dev/mapper/rootvg-rootlv
> > >>> ++ search=/dev/mapper/rootvg-rootlv
> > >>> ++ shift
> > >>> ++ test 0 -gt 0
> > >>> ++ return 1
> > >>> ++ test 4 -ne 4
> > >>> ++ echo / /dev/mapper/rootvg-rootlv /dev/rootvg/rootlv ext3
> > >>> ++ read -a entry
> > >>> ++ IsInArray /boot /srv/prod
> > >>> ++ search=/boot
> > >>> ++ shift
> > >>> ++ test 1 -gt 0
> > >>> ++ test /boot = /srv/prod
> > >>> ++ shift
> > >>> ++ test 0 -gt 0
> > >>> ++ return 1
> > >>> ++ IsInArray /dev/md0
> > >>> ++ search=/dev/md0
> > >>> ++ shift
> > >>> ++ test 0 -gt 0
> > >>> ++ return 1
> > >>> ++ test 4 -ne 4
> > >>> ++ echo /boot /dev/md0 /dev/md0 ext3
> > >>> ++ read -a entry
> > >>> ++ IsInArray /tmp /srv/prod
> > >>> ++ search=/tmp
> > >>> ++ shift
> > >>> ++ test 1 -gt 0
> > >>> ++ test /tmp = /srv/prod
> > >>> ++ shift
> > >>> ++ test 0 -gt 0
> > >>> ++ return 1
> > >>> ++ IsInArray /dev/mapper/rootvg-tmp_lv
> > >>> ++ search=/dev/mapper/rootvg-tmp_lv
> > >>> ++ shift
> > >>> ++ test 0 -gt 0
> > >>> ++ return 1
> > >>> ++ test 4 -ne 4
> > >>> ++ echo /tmp /dev/mapper/rootvg-tmp_lv /dev/rootvg/tmp_lv ext3
> > >>> ++ read -a entry
> > >>> ++ IsInArray /usr /srv/prod
> > >>> ++ search=/usr
> > >>> ++ shift
> > >>> ++ test 1 -gt 0
> > >>> ++ test /usr = /srv/prod
> > >>> ++ shift
> > >>> ++ test 0 -gt 0
> > >>> ++ return 1
> > >>> ++ IsInArray /dev/mapper/rootvg-usr_lv
> > >>> ++ search=/dev/mapper/rootvg-usr_lv
> > >>> ++ shift
> > >>> ++ test 0 -gt 0
> > >>> ++ return 1
> > >>> ++ test 4 -ne 4
> > >>> ++ echo /usr /dev/mapper/rootvg-usr_lv /dev/rootvg/usr_lv ext3
> > >>> ++ read -a entry
> > >>> ++ IsInArray /var /srv/prod
> > >>> ++ search=/var
> > >>> ++ shift
> > >>> ++ test 1 -gt 0
> > >>> ++ test /var = /srv/prod
> > >>> ++ shift
> > >>> ++ test 0 -gt 0
> > >>> ++ return 1
> > >>> ++ IsInArray /dev/mapper/rootvg-var_lv
> > >>> ++ search=/dev/mapper/rootvg-var_lv
> > >>> ++ shift
> > >>> ++ test 0 -gt 0
> > >>> ++ return 1
> > >>> ++ test 4 -ne 4
> > >>> ++ echo /var /dev/mapper/rootvg-var_lv /dev/rootvg/var_lv ext3
> > >>> ++ read -a entry
> > >>> ++ test -s /etc/rear/recovery/mountpoint_device
> > >>> + test 1
> > >>> + set +x
> > >>> 2007-02-13 20:31:51 Including dr/GNU/Linux/12_describe_filesystems.sh
> > >>> + . /usr/share/rear/dr/GNU/Linux/12_describe_filesystems.sh
> > >>> ++ read mountpoint device mountby filesystem junk
> > >>> ++ mkdir -p /etc/rear/recovery/dev/mapper/rootvg-rootlv
> > >>> ++ vol_id /dev/mapper/rootvg-rootlv
> > >>> ++ udev_volume_id /dev/mapper/rootvg-rootlv
> > >>> ++ sed -e 's/^F:\(.*\)$/ID_FS_USAGE='\''\1'\''/' -e 's/^T:
> > >>> \(.*\)$/ID_FS_TYPE='\''\1'\''/' -e 's/^V:\(.*\)$/ID_FS_VERSION='
> > >>> \''\1'\''/' -e 's/^L:\(.*\)$/ID_FS_LABEL='\''\1'\''/' -e 's/^N:
> > >>> \(.*\)/ID_FS_LABEL_SAFE='\''\1'\''/' -e 's/^U:\(.*\)/ID_FS_
> > >>> UUID='\''\1'\''/'
> > >>> ++ grep =
> > >>> ++ Error 'Cannot determine filesystem info
> > >>> on '\''/dev/mapper/rootvg-rootlv'\''
> > >>> Your udev implementation (vol_id or udev_volume_id) does not
> > >>> recognize it.' ++ Log ERROR 'Cannot determine filesystem info
> > >>> on '\''/dev/mapper/rootvg-rootlv'\''
> > >>> Your udev implementation (vol_id or udev_volume_id) does not
> > >>> recognize it.' ++ test 2 -gt 0
> > >>> +++ Stamp
> > >>> +++ date '+%Y-%m-%d %H:%M:%S '
> > >>> ++ echo '2007-02-13 20:31:51 ERROR Cannot determine filesystem info
> > >>> on '\''/dev/mapper/rootvg-rootlv'\''
> > >>> Your udev implementation (vol_id or udev_volume_id) does not
> > >>> recognize it.' 2007-02-13 20:31:51 ERROR Cannot determine filesystem
> > >>> info on '/dev/mapper/rootvg-rootlv'
> > >>> Your udev implementation (vol_id or udev_volume_id) does not
> > >>> recognize it. ++ echo 'ERROR: Cannot determine filesystem info
> > >>> on '\''/dev/mapper/rootvg-rootlv'\''
> > >>> Your udev implementation (vol_id or udev_volume_id) does not
> > >>> recognize it.' ++ exit 1
> > >>> + exec
> > >>>
> > >>>
> > >>> Ciao
> > >>> 	cuni
> > >>>
> > >>> Am Dienstag, 13. Februar 2007 10:16:07 schrieb Christian Neuhold:
> > >>>> Hi,
> > >>>> I tried your new version (rear 1.4) , but no success.
> > >>>>
> > >>>> When I start rear mkbackup on CentOS release 4.4 (Final) I get
> > >>>> following error:
> > >>>>
> > >>>> Relax & Recover Version 1.4 / 2007-02-06
> > >>>> Press ENTER to include '/etc/rear/Linux-i386.conf' ...
> > >>>> Press ENTER to include '/etc/rear/GNU/Linux.conf' ...
> > >>>> Press ENTER to include '/etc/rear/site.conf' ...
> > >>>> Press ENTER to include '/etc/rear/local.conf' ...
> > >>>> Press ENTER to include
> > >>>> '/usr/share/rear/prep/default/01_progress_start.sh' ...
> > >>>> The preparation phase  Press ENTER to include
> > >>>> '/usr/share/rear/prep/ISO/default/30_check_iso_dir.sh' ...
> > >>>> Press ENTER to include
> > >>>> '/usr/share/rear/prep/ISO/default/32_check_cdrom_size.sh' ..|
> > >>>> Press ENTER to include
> > >>>> '/usr/share/rear/prep/ISO/default/33_find_isolinux.sh' ...
> > >>>> Press ENTER to include
> > >>>> '/usr/share/rear/prep/TSM/default/40_prep_tsm.sh' ...
> > >>>> Press ENTER to include
> > >>>> '/usr/share/rear/prep/default/99_progress_stop.sh' ...
> > >>>> OK
> > >>>> Press ENTER to include
> > >>>> '/usr/share/rear/dr/default/01_mk_config_dir_recovery.sh' ...
> > >>>> Press ENTER to include
> > >>>> '/usr/share/rear/dr/GNU/Linux/10_describe_physical_devices.sh' ...
> > >>>> Press ENTER to include
> > >>>> '/usr/share/rear/dr/GNU/Linux/11_describe_mountpoint_device.sh' ...
> > >>>> Press ENTER to include
> > >>>> '/usr/share/rear/dr/GNU/Linux/12_describe_filesystems.sh' ...
> > >>>> ERROR: Cannot determine filesystem info on
> > >>>> '/dev/mapper/rootvg-root_lv' Your udev implementation (vol_id or
> > >>>> udev_volume_id) does not recognize it.
> > >>>>
> > >>>> Ciao
> > >>>>          cuni
> > >>>>
> > >>>> --------------------------------------------------------------------
> > >>>>-- -- - Using Tomcat but need to do more? Need to support web
> > >>>> services, security? Get stuff done quickly with pre-integrated
> > >>>> technology to make your job easier. Download IBM WebSphere
> > >>>> Application Server v.1.0.1 based on Apache Geronimo
> > >>>> http://sel.as-us.falkag.net/sel?cmd=lnk&kid=120709&bid=263057&dat=12
> > >>>>16 42 _______________________________________________
> > >>>> Rear-users mailing list
> > >>>> Rear-users at lists.sourceforge.net
> > >>>> https://lists.sourceforge.net/lists/listinfo/rear-users
> > >>>
> > >>> ---------------------------------------------------------------------
> > >>>-- -- Using Tomcat but need to do more? Need to support web services,
> > >>> security? Get stuff done quickly with pre-integrated technology to
> > >>> make your job easier. Download IBM WebSphere Application Server
> > >>> v.1.0.1 based on Apache Geronimo
> > >>> http://sel.as-us.falkag.net/sel?cmd=lnk&kid=120709&bid=263057&dat=121
> > >>>64 2 _______________________________________________
> > >>> Rear-users mailing list
> > >>> Rear-users at lists.sourceforge.net
> > >>> https://lists.sourceforge.net/lists/listinfo/rear-users
> > >
> > > -----------------------------------------------------------------------
> > >-- Take Surveys. Earn Cash. Influence the Future of IT
> > > Join SourceForge.net's Techsay panel and you'll get the chance to share
> > > your opinions on IT & business topics through brief surveys-and earn
> > > cash
> > > http://www.techsay.com/default.php?page=join.php&p=sourceforge&CID=DEVD
> > >EV _______________________________________________
> > > Rear-users mailing list
> > > Rear-users at lists.sourceforge.net
> > > https://lists.sourceforge.net/lists/listinfo/rear-users
> >
> > -------------------------------------------------------------------------
> > Take Surveys. Earn Cash. Influence the Future of IT
> > Join SourceForge.net's Techsay panel and you'll get the chance to share
> > your opinions on IT & business topics through brief surveys-and earn cash
> > http://www.techsay.com/default.php?page=join.php&p=sourceforge&CID=DEVDEV
> > _______________________________________________
> > Rear-users mailing list
> > Rear-users at lists.sourceforge.net
> > https://lists.sourceforge.net/lists/listinfo/rear-users
>
> -------------------------------------------------------------------------
> Take Surveys. Earn Cash. Influence the Future of IT
> Join SourceForge.net's Techsay panel and you'll get the chance to share
> your opinions on IT & business topics through brief surveys-and earn cash
> http://www.techsay.com/default.php?page=join.php&p=sourceforge&CID=DEVDEV
> _______________________________________________
> Rear-users mailing list
> Rear-users at lists.sourceforge.net
> https://lists.sourceforge.net/lists/listinfo/rear-users




More information about the rear-users mailing list