[Rear-users] ReaR 1.5pre1

Schlomo Schapiro schlomo at schapiro.org
Fri Mar 16 12:30:05 CET 2007


Hi,

thanks for testing !

Maybe the bonding device is not "up" ?

Regards,
Schlomo

Christian Neuhold wrote:
> Hello,
> 
> I tried out your new version. Backup and restore is working great on CentOS 
> 4.4. I tested it
> - with software raid 
> - without software raid
> - with vg and filesystem exclude
> - without vg and filesystem exclude
> 
> I used for restore TSM. PXE and ISO is also working.
> 
> But I have to bind ip address manually. Bonding is not working. I have to 
> check it why. Because device and IP adress exists, but I can't ping any other 
> linux machines.
> 
> Best Regards
> 	Cuni
> 
> 
> Am Montag, 12. März 2007 00:08:01 schrieb Schlomo Schapiro:
>> Hi,
>>
>> attached please find rear 1.5pre1 which should solve the following issues:
>> - bonding
>> - md devices on non-SUSE
>> - cciss
>> - TSM should also backup the resulting files
>>
>> Please give it a try and send me the feedback (positive & negative).
>>
>> Regards,
>> Schlomo
>>
>> PS: Christian, I couldn't run a full test on your VM sine it lacks some
>> crucial software (mount.cifs, mkisofs usw.). But the rear mkrescue ran
>> through cleanly now and the data files in /etcc/rear/recovery look good
>> to me. So please kindly check this RPM on the CentOS VM you have and
>> also do a real backup/recovery.
>>
>> Christian Neuhold wrote:
>>> Hi,
>>>
>>> i only make a minimal rear configuration, I hope this is ok.
>>> My root filesystem is on a logical volume.
>>> rear backup command I use: rear -d -D mkbackup
>>>
>>> vol_id does not exist in Centos 4.4, instead I use udev_volume_id, but I
>>> get "error DEVPATH empty" always.
>>>
>>> udev_volume_id  /dev/mapper/rootvg-root_lv
>>> error DEVPATH empty
>>>
>>> udev_volume_id /dev/rootvg/rootlv
>>> error DEVPATH empty
>>>
>>> udev_volume_id  /dev/sdc
>>> error DEVPATH empty
>>>
>>>
>>>
>>> local.conf
>>> OUTPUT=TSM
>>> MODULES_LOAD=( vmxnet )
>>>
>>> /proc/partitions
>>> major minor  #blocks  name
>>>
>>>    8     0    2097152 sda
>>>    8     1     152586 sda1
>>>    8     2    1943865 sda2
>>>    8    16    2097152 sdb
>>>    8    17     152586 sdb1
>>>    8    18    1943865 sdb2
>>>    9     0     152512 md0
>>>    9     1    1943744 md1
>>>  253     0     262144 dm-0
>>>  253     1     131072 dm-1
>>>  253     2     950272 dm-2
>>>  253     3     425984 dm-3
>>>  253     4     131072 dm-4
>>>    8    32     229376 sdc
>>>  253     5      53248 dm-5
>>>
>>> fstab:
>>> # This file is edited by fstab-sync - see 'man fstab-sync' for details
>>> /dev/rootvg/rootlv      /                       ext3    defaults        1
>>> 1 /dev/md0                /boot                   ext3    defaults       
>>> 1 2 none                    /dev/pts                devpts 
>>> gid=5,mode=620  0 0 none                    /dev/shm                tmpfs
>>>   defaults        0 0 none                    /proc                  
>>> proc    defaults        0 0 none                    /sys                 
>>>   sysfs   defaults        0 0 /dev/rootvg/tmp_lv      /tmp               
>>>     ext3    defaults        1 2 /dev/rootvg/usr_lv      /usr             
>>>       ext3    defaults        1 2 /dev/rootvg/var_lv      /var           
>>>         ext3    defaults        1 2 /dev/rootvg/swap_lv     swap         
>>>           swap    defaults        0 0 /dev/datavg/prod_lv     /srv/prod  
>>>             ext3    defaults,noauto 0 0 /dev/hdc               
>>> /media/cdrom            auto
>>> pamconsole,exec,noauto,managed 0 0
>>> /dev/fd0                /media/floppy           auto
>>> pamconsole,exec,noauto,managed 0 0
>>>
>>>
>>> /tmp/rear.log
>>> 2007-02-13 20:31:35 Relax & Recover Version 1.4 / 2007-02-06
>>> 2007-02-13 20:31:35 Combining configuration files
>>> 2007-02-13 20:31:35 Skipping /etc/rear/mkbackup.conf (file not found or
>>> empty) 2007-02-13 20:31:35 Including /etc/rear/Linux-i386.conf
>>> 2007-02-13 20:31:35 Including /etc/rear/GNU/Linux.conf
>>> 2007-02-13 20:31:35 Skipping /etc/rear/CentOS.conf (file not found or
>>> empty) 2007-02-13 20:31:35 Skipping /etc/rear/CentOS/i386.conf (file not
>>> found or empty)
>>> 2007-02-13 20:31:35 Skipping /etc/rear/CentOS/4.4.conf (file not found or
>>> empty)
>>> 2007-02-13 20:31:35 Including /etc/rear/site.conf
>>> 2007-02-13 20:31:35 Including /etc/rear/local.conf
>>> 2007-02-13 20:31:36 Creating build area '/tmp/rear.4065'
>>> 2007-02-13 20:31:36 Running mkbackup workflow
>>> 2007-02-13 20:31:36 Running 'prep' stage
>>> 2007-02-13 20:31:36 Including prep/default/01_progress_start.sh
>>> 2007-02-13 20:31:36 Including prep/TSM/default/40_prep_tsm.sh
>>> 2007-02-13 20:31:36 Including prep/default/99_progress_stop.sh
>>> 2007-02-13 20:31:36 Finished running 'prep' stage in 0 seconds
>>> 2007-02-13 20:31:36 Running 'dr' stage
>>> 2007-02-13 20:31:36 Including dr/default/01_mk_config_dir_recovery.sh
>>> 2007-02-13 20:31:36 Including
>>> dr/GNU/Linux/10_describe_physical_devices.sh 2007-02-13 20:31:36 Skipping
>>> small removable device 'hdc' [Size: 3GB]. Adjust
>>> SYSFS_REMOVABLE_DEVICE_SIZE [15] to prevent
>>> this.
>>> 2007-02-13 20:31:36 Including
>>> dr/GNU/Linux/11_describe_mountpoint_device.sh 2007-02-13 20:31:36
>>> Including dr/GNU/Linux/12_describe_filesystems.sh 2007-02-13 20:31:36
>>> ERROR Cannot determine filesystem info
>>> on '/dev/mapper/rootvg-rootlv'
>>> Your udev implementation (vol_id or udev_volume_id) does not recognize
>>> it. [root at CNCCENTOS01 /]# rm -rf /tmp/rear.*
>>> rear mkbackup -d
>>> [root at CNCCENTOS01 /]# rear -d -D mkbackup
>>> Relax & Recover Version 1.4 / 2007-02-06
>>> The preparation phase OK
>>> ERROR: Cannot determine filesystem info on '/dev/mapper/rootvg-rootlv'
>>> Your udev implementation (vol_id or udev_volume_id) does not recognize
>>> it. [root at CNCCENTOS01 /]# cat /tmp/rear.
>>> cat: /tmp/rear.: No such file or directory
>>> [root at CNCCENTOS01 /]# cat /tmp/rear.log
>>> 2007-02-13 20:31:51 Relax & Recover Version 1.4 / 2007-02-06
>>> 2007-02-13 20:31:51 Combining configuration files
>>> 2007-02-13 20:31:51 Skipping /etc/rear/mkbackup.conf (file not found or
>>> empty) 2007-02-13 20:31:51 Including /etc/rear/Linux-i386.conf
>>> + . /etc/rear/Linux-i386.conf
>>> ++ REQUIRED_PROGS=("${REQUIRED_PROGS[@]}" sfdisk)
>>> ++ PROGS=("${PROGS[@]}" grub partprobe parted lilo fdisk cfdisk)
>>> + test 1
>>> + set +x
>>> 2007-02-13 20:31:51 Including /etc/rear/GNU/Linux.conf
>>> + . /etc/rear/GNU/Linux.conf
>>> ++ PROGS=(${PROGS[@]} bash mknod vol_id udev_volume_id portmap readlink
>>> rpcinfo grep cat tr reboot halt shutdown killall5
>>> killall chroot tee awk ip ifenslave klogd syslog-ng syslogd echo cp date
>>> wc cut rm test init ethtool expand sed mount umou
>>> nt insmod modprobe lsmod true false mingetty rmmod hostname uname sleep
>>> logger ps ln dirname basename mkdir cpio tty ping
>>> netstat free traceroute less vi rmmod df ls dmesg du tar gzip netcat top
>>> iptraf joe pico getent id nslookup ldd strace rsy
>>> nc tail head find md5sum mkfs mkfs.ext2 mkfs.ext3 mkfs.jfs mkfs.xfs
>>> mkfs.reiserfs mkreiserfs fsck.ext2 fsck.ext3 fsck.xfs
>>> fsck.reiserfs reiserfsck tune2fs xfs_admin xfs_db jfs_tune reiserfstune
>>> fsck expr egrep grep fgrep df chmod chown stat mks
>>> wap swapon swapoff mknod)
>>> ++ LIBS=(${LIBS[@]} /lib/libnss_dns* /lib/libnss_files* /lib/libgcc_s*)
>>> ++ MODULES=(${MODULES[@]} af_packet unix nfs lockd sunrpc cifs)
>>> ++
>>> COPY_AS_IS=(${COPY_AS_IS[@]} /dev /etc/protocols /etc/services /etc/rpc
>>> /etc/termcap /usr/share/terminfo) + test 1
>>> + set +x
>>> 2007-02-13 20:31:51 Skipping /etc/rear/CentOS.conf (file not found or
>>> empty) 2007-02-13 20:31:51 Skipping /etc/rear/CentOS/i386.conf (file not
>>> found or empty)
>>> 2007-02-13 20:31:51 Skipping /etc/rear/CentOS/4.4.conf (file not found or
>>> empty)
>>> 2007-02-13 20:31:51 Including /etc/rear/site.conf
>>> + . /etc/rear/site.conf
>>> + test 1
>>> + set +x
>>> 2007-02-13 20:31:51 Including /etc/rear/local.conf
>>> + . /etc/rear/local.conf
>>> ++ OUTPUT=TSM
>>> ++ MODULES_LOAD=(vmxnet)
>>> + test 1
>>> + set +x
>>> 2007-02-13 20:31:51 Creating build area '/tmp/rear.4263'
>>> 2007-02-13 20:31:51 Running mkbackup workflow
>>> 2007-02-13 20:31:51 Running 'prep' stage
>>> 2007-02-13 20:31:51 Including prep/default/01_progress_start.sh
>>> + . /usr/share/rear/prep/default/01_progress_start.sh
>>> ++ ProgressStart 'The preparation phase'
>>> ++ echo -n 'The preparation phase  '
>>> ++ kill -USR2 4296
>>> + test 1
>>> + set +x
>>> 2007-02-13 20:31:51 Including prep/TSM/default/40_prep_tsm.sh
>>> + . /usr/share/rear/prep/TSM/default/40_prep_tsm.sh
>>> ++ COPY_AS_IS=("${COPY_AS_IS[@]}" "${COPY_AS_IS_TSM[@]}")
>>> ++
>>> COPY_AS_IS_EXCLUDE=("${COPY_AS_IS_EXCLUDE[@]}"
>>> "${COPY_AS_IS_EXCLUDE_TSM[@]}") ++ PROGS=("${PROGS[*]}"
>>> "${PROGS_TSM[*]}")
>>> + test 1
>>> + set +x
>>> 2007-02-13 20:31:51 Including prep/default/99_progress_stop.sh
>>> + . /usr/share/rear/prep/default/99_progress_stop.sh
>>> ++ ProgressStop
>>> ++ kill -USR1 4296
>>> ++ echo -e '\bOK'
>>> + test 1
>>> + set +x
>>> 2007-02-13 20:31:51 Finished running 'prep' stage in 0 seconds
>>> 2007-02-13 20:31:51 Running 'dr' stage
>>> 2007-02-13 20:31:51 Including dr/default/01_mk_config_dir_recovery.sh
>>> + . /usr/share/rear/dr/default/01_mk_config_dir_recovery.sh
>>> ++ rm -Rf /etc/rear/recovery
>>> ++ mkdir -m 755 /etc/rear/recovery
>>> + test 1
>>> + set +x
>>> 2007-02-13 20:31:51 Including
>>> dr/GNU/Linux/10_describe_physical_devices.sh + .
>>> /usr/share/rear/dr/GNU/Linux/10_describe_physical_devices.sh ++
>>> FindPhysicalDevices
>>> +++
>>> ls -d /sys/block/hdc/device /sys/block/sda/device /sys/block/sdb/device
>>> /sys/block/sdc/device ++ for d in '$(ls -d /sys/block/*/device)'
>>> ++ test -L /sys/block/hdc/device
>>> +++ dirname /sys/block/hdc/device
>>> ++ sysfspath=/sys/block/hdc
>>> +++ basename /sys/block/hdc
>>> ++ device=hdc
>>> ++ test -s /sys/block/hdc/size
>>> +++ cat /sys/block/hdc/size
>>> ++ sysfssize=8388604
>>> +++ cat /sys/block/hdc/removable
>>> ++ test 1 -eq 1 -a 3 -le 15
>>> ++ Log 'Skipping small removable device '\''hdc'\'' [Size: 3GB]. Adjust
>>> SYSFS_REMOVABLE_DEVICE_SIZE [15] to prevent this.'
>>> ++ test 1 -gt 0
>>> +++ Stamp
>>> +++ date '+%Y-%m-%d %H:%M:%S '
>>> ++ echo '2007-02-13 20:31:51 Skipping small removable device '\''hdc'\''
>>> [Size: 3GB]. Adjust SYSFS_REMOVABLE_DEVICE_SIZE [
>>> 15] to prevent this.'
>>> 2007-02-13 20:31:51 Skipping small removable device 'hdc' [Size: 3GB].
>>> Adjust SYSFS_REMOVABLE_DEVICE_SIZE [15] to prevent
>>> this.
>>> ++ continue
>>> ++ for d in '$(ls -d /sys/block/*/device)'
>>> ++ test -L /sys/block/sda/device
>>> +++ dirname /sys/block/sda/device
>>> ++ sysfspath=/sys/block/sda
>>> +++ basename /sys/block/sda
>>> ++ device=sda
>>> ++ test -s /sys/block/sda/size
>>> +++ cat /sys/block/sda/size
>>> ++ sysfssize=4194304
>>> +++ cat /sys/block/sda/removable
>>> ++ test 0 -eq 1 -a 2 -le 15
>>> ++ DeviceNameToNode sda
>>> ++ device=/dev/sda
>>> ++ device2=/dev/sda
>>> ++ test -b /dev/sda
>>> ++ echo /dev/sda
>>> ++ for d in '$(ls -d /sys/block/*/device)'
>>> ++ test -L /sys/block/sdb/device
>>> +++ dirname /sys/block/sdb/device
>>> ++ sysfspath=/sys/block/sdb
>>> +++ basename /sys/block/sdb
>>> ++ device=sdb
>>> ++ test -s /sys/block/sdb/size
>>> +++ cat /sys/block/sdb/size
>>> ++ sysfssize=4194304
>>> +++ cat /sys/block/sdb/removable
>>> ++ test 0 -eq 1 -a 2 -le 15
>>> ++ DeviceNameToNode sdb
>>> ++ device=/dev/sdb
>>> ++ device2=/dev/sdb
>>> ++ test -b /dev/sdb
>>> ++ echo /dev/sdb
>>> ++ for d in '$(ls -d /sys/block/*/device)'
>>> ++ test -L /sys/block/sdc/device
>>> +++ dirname /sys/block/sdc/device
>>> ++ sysfspath=/sys/block/sdc
>>> +++ basename /sys/block/sdc
>>> ++ device=sdc
>>> ++ test -s /sys/block/sdc/size
>>> +++ cat /sys/block/sdc/size
>>> ++ sysfssize=458752
>>> +++ cat /sys/block/sdc/removable
>>> ++ test 0 -eq 1 -a 0 -le 15
>>> ++ DeviceNameToNode sdc
>>> ++ device=/dev/sdc
>>> ++ device2=/dev/sdc
>>> ++ test -b /dev/sdc
>>> ++ echo /dev/sdc
>>> + test 1
>>> + set +x
>>> 2007-02-13 20:31:51 Including
>>> dr/GNU/Linux/11_describe_mountpoint_device.sh + .
>>> /usr/share/rear/dr/GNU/Linux/11_describe_mountpoint_device.sh ++ echo -n
>>> ''
>>> ++++ mount
>>> ++++ cut -d ' ' -f 1,3
>>> ++++ grep -v noauto /etc/fstab
>>> +++ join -a 2 -j 2 /dev/fd/63 /dev/fd/62
>>> ++ read -a entry
>>> ++++ grep -v '^#'
>>> ++++ tr -s ' \t' ' '
>>> ++++ cut -s -d ' ' -f 1,2,3
>>> ++++ sort -k 2
>>> ++++ sort -k 2 -t ' '
>>> ++++ grep -E '(reiserfs|xfs|ext|jfs)'
>>> ++ IsInArray / /srv/prod
>>> ++ search=/
>>> ++ shift
>>> ++ test 1 -gt 0
>>> ++ test / = /srv/prod
>>> ++ shift
>>> ++ test 0 -gt 0
>>> ++ return 1
>>> ++ IsInArray /dev/mapper/rootvg-rootlv
>>> ++ search=/dev/mapper/rootvg-rootlv
>>> ++ shift
>>> ++ test 0 -gt 0
>>> ++ return 1
>>> ++ test 4 -ne 4
>>> ++ echo / /dev/mapper/rootvg-rootlv /dev/rootvg/rootlv ext3
>>> ++ read -a entry
>>> ++ IsInArray /boot /srv/prod
>>> ++ search=/boot
>>> ++ shift
>>> ++ test 1 -gt 0
>>> ++ test /boot = /srv/prod
>>> ++ shift
>>> ++ test 0 -gt 0
>>> ++ return 1
>>> ++ IsInArray /dev/md0
>>> ++ search=/dev/md0
>>> ++ shift
>>> ++ test 0 -gt 0
>>> ++ return 1
>>> ++ test 4 -ne 4
>>> ++ echo /boot /dev/md0 /dev/md0 ext3
>>> ++ read -a entry
>>> ++ IsInArray /tmp /srv/prod
>>> ++ search=/tmp
>>> ++ shift
>>> ++ test 1 -gt 0
>>> ++ test /tmp = /srv/prod
>>> ++ shift
>>> ++ test 0 -gt 0
>>> ++ return 1
>>> ++ IsInArray /dev/mapper/rootvg-tmp_lv
>>> ++ search=/dev/mapper/rootvg-tmp_lv
>>> ++ shift
>>> ++ test 0 -gt 0
>>> ++ return 1
>>> ++ test 4 -ne 4
>>> ++ echo /tmp /dev/mapper/rootvg-tmp_lv /dev/rootvg/tmp_lv ext3
>>> ++ read -a entry
>>> ++ IsInArray /usr /srv/prod
>>> ++ search=/usr
>>> ++ shift
>>> ++ test 1 -gt 0
>>> ++ test /usr = /srv/prod
>>> ++ shift
>>> ++ test 0 -gt 0
>>> ++ return 1
>>> ++ IsInArray /dev/mapper/rootvg-usr_lv
>>> ++ search=/dev/mapper/rootvg-usr_lv
>>> ++ shift
>>> ++ test 0 -gt 0
>>> ++ return 1
>>> ++ test 4 -ne 4
>>> ++ echo /usr /dev/mapper/rootvg-usr_lv /dev/rootvg/usr_lv ext3
>>> ++ read -a entry
>>> ++ IsInArray /var /srv/prod
>>> ++ search=/var
>>> ++ shift
>>> ++ test 1 -gt 0
>>> ++ test /var = /srv/prod
>>> ++ shift
>>> ++ test 0 -gt 0
>>> ++ return 1
>>> ++ IsInArray /dev/mapper/rootvg-var_lv
>>> ++ search=/dev/mapper/rootvg-var_lv
>>> ++ shift
>>> ++ test 0 -gt 0
>>> ++ return 1
>>> ++ test 4 -ne 4
>>> ++ echo /var /dev/mapper/rootvg-var_lv /dev/rootvg/var_lv ext3
>>> ++ read -a entry
>>> ++ test -s /etc/rear/recovery/mountpoint_device
>>> + test 1
>>> + set +x
>>> 2007-02-13 20:31:51 Including dr/GNU/Linux/12_describe_filesystems.sh
>>> + . /usr/share/rear/dr/GNU/Linux/12_describe_filesystems.sh
>>> ++ read mountpoint device mountby filesystem junk
>>> ++ mkdir -p /etc/rear/recovery/dev/mapper/rootvg-rootlv
>>> ++ vol_id /dev/mapper/rootvg-rootlv
>>> ++ udev_volume_id /dev/mapper/rootvg-rootlv
>>> ++ sed -e 's/^F:\(.*\)$/ID_FS_USAGE='\''\1'\''/' -e 's/^T:
>>> \(.*\)$/ID_FS_TYPE='\''\1'\''/' -e 's/^V:\(.*\)$/ID_FS_VERSION='
>>> \''\1'\''/' -e 's/^L:\(.*\)$/ID_FS_LABEL='\''\1'\''/' -e 's/^N:
>>> \(.*\)/ID_FS_LABEL_SAFE='\''\1'\''/' -e 's/^U:\(.*\)/ID_FS_
>>> UUID='\''\1'\''/'
>>> ++ grep =
>>> ++ Error 'Cannot determine filesystem info
>>> on '\''/dev/mapper/rootvg-rootlv'\''
>>> Your udev implementation (vol_id or udev_volume_id) does not recognize
>>> it.' ++ Log ERROR 'Cannot determine filesystem info
>>> on '\''/dev/mapper/rootvg-rootlv'\''
>>> Your udev implementation (vol_id or udev_volume_id) does not recognize
>>> it.' ++ test 2 -gt 0
>>> +++ Stamp
>>> +++ date '+%Y-%m-%d %H:%M:%S '
>>> ++ echo '2007-02-13 20:31:51 ERROR Cannot determine filesystem info
>>> on '\''/dev/mapper/rootvg-rootlv'\''
>>> Your udev implementation (vol_id or udev_volume_id) does not recognize
>>> it.' 2007-02-13 20:31:51 ERROR Cannot determine filesystem info
>>> on '/dev/mapper/rootvg-rootlv'
>>> Your udev implementation (vol_id or udev_volume_id) does not recognize
>>> it. ++ echo 'ERROR: Cannot determine filesystem info
>>> on '\''/dev/mapper/rootvg-rootlv'\''
>>> Your udev implementation (vol_id or udev_volume_id) does not recognize
>>> it.' ++ exit 1
>>> + exec
>>>
>>>
>>> Ciao
>>> 	cuni
>>>
>>> Am Dienstag, 13. Februar 2007 10:16:07 schrieb Christian Neuhold:
>>>> Hi,
>>>> I tried your new version (rear 1.4) , but no success.
>>>>
>>>> When I start rear mkbackup on CentOS release 4.4 (Final) I get following
>>>> error:
>>>>
>>>> Relax & Recover Version 1.4 / 2007-02-06
>>>> Press ENTER to include '/etc/rear/Linux-i386.conf' ...
>>>> Press ENTER to include '/etc/rear/GNU/Linux.conf' ...
>>>> Press ENTER to include '/etc/rear/site.conf' ...
>>>> Press ENTER to include '/etc/rear/local.conf' ...
>>>> Press ENTER to include
>>>> '/usr/share/rear/prep/default/01_progress_start.sh' ...
>>>> The preparation phase  Press ENTER to include
>>>> '/usr/share/rear/prep/ISO/default/30_check_iso_dir.sh' ...
>>>> Press ENTER to include
>>>> '/usr/share/rear/prep/ISO/default/32_check_cdrom_size.sh' ..|
>>>> Press ENTER to include
>>>> '/usr/share/rear/prep/ISO/default/33_find_isolinux.sh' ...
>>>> Press ENTER to include '/usr/share/rear/prep/TSM/default/40_prep_tsm.sh'
>>>> ...
>>>> Press ENTER to include
>>>> '/usr/share/rear/prep/default/99_progress_stop.sh' ...
>>>> OK
>>>> Press ENTER to include
>>>> '/usr/share/rear/dr/default/01_mk_config_dir_recovery.sh' ...
>>>> Press ENTER to include
>>>> '/usr/share/rear/dr/GNU/Linux/10_describe_physical_devices.sh' ...
>>>> Press ENTER to include
>>>> '/usr/share/rear/dr/GNU/Linux/11_describe_mountpoint_device.sh' ...
>>>> Press ENTER to include
>>>> '/usr/share/rear/dr/GNU/Linux/12_describe_filesystems.sh' ...
>>>> ERROR: Cannot determine filesystem info on '/dev/mapper/rootvg-root_lv'
>>>> Your udev implementation (vol_id or udev_volume_id) does not recognize
>>>> it.
>>>>
>>>> Ciao
>>>>          cuni
>>>>
>>>> ------------------------------------------------------------------------
>>>> - Using Tomcat but need to do more? Need to support web services,
>>>> security? Get stuff done quickly with pre-integrated technology to make
>>>> your job easier. Download IBM WebSphere Application Server v.1.0.1 based
>>>> on Apache Geronimo
>>>> http://sel.as-us.falkag.net/sel?cmd=lnk&kid=120709&bid=263057&dat=121642
>>>> _______________________________________________
>>>> Rear-users mailing list
>>>> Rear-users at lists.sourceforge.net
>>>> https://lists.sourceforge.net/lists/listinfo/rear-users
>>> -------------------------------------------------------------------------
>>> Using Tomcat but need to do more? Need to support web services, security?
>>> Get stuff done quickly with pre-integrated technology to make your job
>>> easier. Download IBM WebSphere Application Server v.1.0.1 based on Apache
>>> Geronimo
>>> http://sel.as-us.falkag.net/sel?cmd=lnk&kid=120709&bid=263057&dat=121642
>>> _______________________________________________
>>> Rear-users mailing list
>>> Rear-users at lists.sourceforge.net
>>> https://lists.sourceforge.net/lists/listinfo/rear-users
> 
> -------------------------------------------------------------------------
> Take Surveys. Earn Cash. Influence the Future of IT
> Join SourceForge.net's Techsay panel and you'll get the chance to share your
> opinions on IT & business topics through brief surveys-and earn cash
> http://www.techsay.com/default.php?page=join.php&p=sourceforge&CID=DEVDEV
> _______________________________________________
> Rear-users mailing list
> Rear-users at lists.sourceforge.net
> https://lists.sourceforge.net/lists/listinfo/rear-users




More information about the rear-users mailing list